The Thetford Aqua Magic Style II is a popular and reliable toilet system used in RVs and boats. Over time, certain parts of the system may wear out or become damaged, requiring replacement. Thankfully, Thetford offers a range of replacement parts specifically designed for the Aqua Magic Style II. One commonly replaced part is the flush ball seal. This component ensures a tight seal between the toilet bowl and the flush ball, preventing leaks and odors. If you notice any leaks or unpleasant odors coming from your toilet, it may be time to replace the flush ball seal.
It isn't hard at all and, truth be told, I should have been it done a while back. The Style II is made to be easily removed AND maintained. I have to say that the mechanical parts could be made out of brass or metal instead of plastic but the design cannot be better for maintenance. I ordered all the parts on Amazon and it cost about $75. Two screws to pull the toilet out- 3 minutes. Placed a doubled up rug on the tailgate of my truck and laid the unit down on its side. Watched the Youtube video on removing and installing the pedal. Removed/replaced gate ball arm after greasing with plumbers grease, greased spring and replace water valve and vacuum breaker. Replaced pedal- paying attention to placement of spring into pedal = 45 minutes. (Because I wasn't paying attention to that danged spring placement.) I could do all that now in less than 10 minutes. Set the toilet up and removed two screws from behind- turned the bowl counter -clockwise and removed porcelain upper. Removed/replaced the gate ball and seal after applying plumbers silicon grease. Replaced the upper and screwed the two screws back in. Pay attention and make sure you use the plastic washers first against the porcelain and do not over- tighten. Replace closet bowl seal and reinstall the toilet. BAM - all in about an hour and most of you could probably do it in less that thirty minutes once you know how. So the Style II is made to be easily serviced and maintained. Of course I drained the Blank tank first and I cleaned the toilet prior to removal. I used latex gloves but man, this was really easy. I am thinking maybe you should rebuild maybe every 225 nights if you use the commode like one does in the sticks and bricks. (OK..maybe I over did it with the plumbers grease but I always say if a little bit is good then a lot must be better.)
When you shop at Boat RV Accessories, you ll find everything you need for your boat, camper, fifth wheel, motorhome, popup, RV, travel trailer, or truck camper. When you shop at Boat RV Accessories, you ll find everything you need for your boat, camper, fifth wheel, motorhome, popup, RV, travel trailer, or truck camper.
If you notice any leaks or unpleasant odors coming from your toilet, it may be time to replace the flush ball seal. Another important part that may need replacement is the water valve. This valve is responsible for controlling the flow of water into the toilet bowl.
Justaguy
Here ya go Lily F. Was asked to put this on our website.
I was dreading this job - REALLY dreading this job. But there may be others out there that have a Style II and are hesitant to start.
It isn't hard at all and, truth be told, I should have been it done a while back. The Style II is made to be easily removed AND maintained. I have to say that the mechanical parts could be made out of brass or metal instead of plastic but the design cannot be better for maintenance. I ordered all the parts on Amazon and it cost about $75. Two screws to pull the toilet out- 3 minutes. Placed a doubled up rug on the tailgate of my truck and laid the unit down on its side. Watched the Youtube video on removing and installing the pedal. Removed/replaced gate ball arm after greasing with plumbers grease, greased spring and replace water valve and vacuum breaker. Replaced pedal- paying attention to placement of spring into pedal = 45 minutes. (Because I wasn't paying attention to that danged spring placement.) I could do all that now in less than 10 minutes. Set the toilet up and removed two screws from behind- turned the bowl counter -clockwise and removed porcelain upper. Removed/replaced the gate ball and seal after applying plumbers silicon grease. Replaced the upper and screwed the two screws back in. Pay attention and make sure you use the plastic washers first against the porcelain and do not over- tighten. Replace closet bowl seal and reinstall the toilet. BAM - all in about an hour and most of you could probably do it in less that thirty minutes once you know how. So the Style II is made to be easily serviced and maintained. Of course I drained the Blank tank first and I cleaned the toilet prior to removal. I used latex gloves but man, this was really easy. I am thinking maybe you should rebuild maybe every 225 nights if you use the commode like one does in the sticks and bricks. (OK..maybe I over did it with the plumbers grease but I always say if a little bit is good then a lot must be better.)
Some may prefer to replace this toilet with a different brand when these Style II's malfunction. That's feasible too since a new rebuild kits (4) were about $75 and a new quality toilet is $150 or so on Amazon.
So there ya go. if you have a Style II, get 'er done. It's not as bad as some people think.
Categories Uncategorized- Email Blog Entry
Here ya go Lily F. Was asked to put this on our website.
Over time, it may become clogged or malfunction, causing issues with flushing. Replacing the water valve can solve these problems and restore the flush functionality. Additionally, the blade seal and the blade mechanism itself may require replacement. The blade seal is responsible for creating a watertight seal when the toilet is not in use, while the blade mechanism controls the smooth operation of the flush ball. If you notice any difficulties in opening or closing the flush ball, or if you notice any leaks when the toilet is not in use, it may be necessary to replace these parts. Thetford also offers replacement kits that include multiple parts, making it easier to ensure you have everything you need for a complete replacement. These kits typically include the necessary seals, valves, and other components for a thorough overhaul of the Aqua Magic Style II system. When replacing any parts, it is important to follow the manufacturer's instructions and take proper safety precautions. Thetford provides detailed instructions with each replacement part, making the process as straightforward as possible. In conclusion, the Thetford Aqua Magic Style II is a reliable and popular toilet system used in RVs and boats. Over time, certain parts may need replacement to maintain optimal functionality. Thetford offers a range of replacement parts, including flush ball seals, water valves, blade seals, and blade mechanisms. By following the manufacturer's instructions and taking proper safety precautions, it is possible to replace these parts and restore the performance of the Aqua Magic Style II system..
Reviews for "Tips for Finding High-Quality Thetford Aqua Magic Style II Replacement Parts"
1. John - 1 star - I was extremely disappointed with the Thetford Aqua Magic Style II replacement parts. I purchased them hoping to fix my broken toilet, but they ended up being more trouble than they were worth. The parts were difficult to install and didn't fit properly, causing leaks and other issues. I ended up having to buy different replacement parts from a different brand, which worked much better. I would not recommend these Thetford parts to anyone.
2. Sarah - 2 stars - I had high hopes for the Thetford Aqua Magic Style II replacement parts, but they just didn't live up to my expectations. The installation process was frustrating and time-consuming, and even after it was finally installed, the toilet still didn't work properly. The flush mechanism was weak and often got stuck, causing constant clogs. I tried tweaking and adjusting the parts, but nothing seemed to help. Overall, I was disappointed with the performance of these replacement parts.
3. Mike - 1 star - The Thetford Aqua Magic Style II replacement parts were a waste of money for me. I followed the instructions carefully and spent hours trying to install them correctly, but they just didn't fit properly. The flush handle was loose and wobbly, and the water flow was inconsistent. It was frustrating to spend so much time and effort only to end up with a poorly functioning toilet. I would not recommend these replacement parts to anyone in need of reliable and efficient repairs.
4. Lisa - 2 stars - I had heard good things about Thetford products, so I decided to give their Aqua Magic Style II replacement parts a try. Unfortunately, they fell short of my expectations. The parts were difficult to install, and even after I managed to get them in place, the toilet still had leaks and flush problems. I ended up having to hire a professional to fix the issues, which cost me even more money. I was disappointed with the quality and performance of these replacement parts.
5. Robert - 1 star - I regret purchasing the Thetford Aqua Magic Style II replacement parts. Despite following the installation instructions carefully, the parts didn't fit properly and caused more problems than I had initially. The toilet constantly leaked and the flush mechanism was unreliable. I ended up having to call a plumber to fix the issues, which turned out to be a waste of my time and money. I would not recommend these replacement parts to anyone in need of a reliable and hassle-free solution.