Magic Smoke Electronics refers to a humorous phrase used to describe the release of smoke or the failure of electronic components. It is often used when an electronic device or component is damaged due to overloading or a fault in the system. The phrase "magic smoke" comes from the idea that electronic devices work based on the flow of electrical current and when this flow is interrupted or excessive, it can cause the release of smoke, which is often associated with a malfunction or failure of the device. The concept of magic smoke electronics is used as a lighthearted way to explain the consequences of mishandling or improper use of electronic devices. It serves as a reminder to be cautious and follow proper procedures to avoid damaging electronic components or causing potential hazards. Magic smoke electronics can occur in various scenarios, such as when a fuse is blown, a circuit breaker trips, or when a component is overloaded beyond its capacity.
In some variations of the joke, it is alleged that the major microchip production companies (especially the large microprocessor manufacturers) are involved in a conspiracy to keep the true nature of their products under wraps.
The magic smoke is observed to come out of electronic components when overheated, often through exposure to an extreme electrical current usually caused by the application of excess voltage through some failure of the circuit. The shorts we see can be caused by anything from contamination, like a water spill acting as a conductor between two circuits, to employee mishap, such as a loose screw falling across two uninsulated conductors or finally improper wiring and hookup.
Magic smoke electronics can occur in various scenarios, such as when a fuse is blown, a circuit breaker trips, or when a component is overloaded beyond its capacity. In these situations, the release of smoke is a visible indication of a problem in the circuit or device. To prevent magic smoke electronics, it is crucial to understand the specifications and limitations of electronic components and devices.
Top 10 Causes of Magic Smoke
A single key supply chain component shortage puts manufacturing in a line-down situation.
Supply Chain Management for Electronics Manufacturing
Choreograph with your team and CM to achieve smooth electronics logistics planning. Our short blog will provide you tips and tricks.
Other Resources
Certifications
Circuit Break Podcast
Blog
eBooks & Guides
Webinars
Videos
Case Studies
MacroFab Platform Help
On occasion, the excitement of seeing a new system operate for the first time is deflating when a component releases your arch-nemesis – magic smoke. The system may not function if there is a critical error preventing operation. While this can be frustrating, there are several areas for design review that can mitigate this problem and should be included in your next project to achieve first success in the future. Let’s take a look at the top ten areas to prevent your boards from releasing magic smoke.
Screen Shot 2019 11 01 at 2
Make the Right Connections
Ahead of the system PCB fabrication tapeout, a detailed design overview for each component pin is needed. This includes not only power and ground pins, but also all the digital I/O, control, analog and do not connect (DNC) pins. The functional operation of each pin should be compared against the signal input device. The specified minimum and maximum voltage and current of each should be compared against the worst signal cases. DNC pins should be soldered to an open to maintain mechanical integrity. Complex design software tools should do this automatically, but the results will only be as good as the component library information that was input by a human. A final pin review often identifies subtle issues.
Take a Hard Look at the Mirroring
Screen Shot 2019 11 01 at 2
Screen Shot 2019 11 01 at 2 1
In an effort to make a component fit into a difficult location on a PCB, a layout engineer may often rotate and flip component decals to minimize the active routing area. Sometimes a component decal can be inadvertently mirrored. A true mirror of a component, without placement on an opposite PCB surface, will be assembly prohibitive. Componentlayout using multiple sides to a PCB can invert a component inadvertently. The layout tool should alert the user to this situation, but a final review of all components before PCB fabrication is often the best approach. Also, ensure that the pinout decal matches the component pinout to prevent library errors.
Showcase the Right Model
All components, both active and passive, come in a variety of functional variants. Package form factor, tolerance, speed rating, and power ratings are just some of the differences that can separate one similar component from another. Ensure that your BOM accurately describes the exact component variant that your design requires. Once the BOM is ordered, your contract manufacturer will verify that the received components match the BOM listing to be used within the PCB assembly. Many components look the same but have different electrical pinouts. A model difference in one component has the potential to cause the first system build to be non-operational.
Narrow pitch Ball Grid Array (BGA) devices and Small Outline Transistor (SOT) components are efficient in minimizing system area. Resistors and capacitors smaller than 0201 dimensions are becoming more commonplace for new designs. However, without proper solder pad openings and spacing on the layout, their small solder footprint can lead to bridging and cold solder joints. A review of the solder screenprint for the system PCB should be completed against the assembly requirements to eliminate layout issues stemming from poor solder connections. Although layout tools should flag design rule violations for spacing issues, specific assembly challenged areas may need to be added to your ruleset. Your CM can review the assembly equipment spacing capability against your design to mitigate these solder pitch issues.
Each active component may need a current limit on its respective pins to prevent tri-state events that can draw excessive current. While many digital I/O and control signals offer internal pull-up and pull-down resistors, some legacy components do not. Normally, a high or low signal will be driven with the proper termination on the other end of the transmission line. However, if neither a high nor low is driven, the pin has the potential to be left floating in a logical unknown or tri-state. This case can pull unwanted current and power from the supply when an entire digital bus is left in this state. An external resistor that is tied to GND or supply may be needed for those components that do not offer internal terminations. A supply line to an active component may also need a current limiter to prevent a runaway thermal situation where the component draws excessive current beyond its capability.
Additional protection circuitry may be required to protect the system from surge current type events that could damage the electronics. Whether the surge occurs at first power-up or is a discrete abnormal event, the intent is to protect the system from the offending signal. Often, this can be done with Zener diodes and other clamping devices. If the assembly is a sub-system within a larger more complex system, the connectors and any cable interfaces should have a Poka-Yoke strategy to prevent mis-insertion. This approach creates a fool-proof method to ensure that the system is properly connected. An everyday example of this is the three-prong electrical outlet plug in the USA that only affords one orientation for proper insertion.
Review Failure Modes
A complex system may have many potential ways that it could fail, often including some that are not intuitive. Many organizations require a complete Design Failure Mode Effects Analysis (DFMEA) review to determine and review all these modes of operation that could fail. This is generally a good practice if for nothing else than to identify weaknesses in the design. After identification, each failure mode will be scored based on its severity, probability of occurrence, and method of detection. A risk priority number can be calculated to determine the most impactful failure types. The worst offenders should be addressed within the design or test methods to improve the system performance and reduce the opportunity for smoke.
Address the Outside Concerns
An electrical system is not self-contained as it must accept interference from the external environment. A power surge or ground bounce has the potential to damage the system. Large RF signals may damage a radio receiver that is designed only to observe small signals without the proper filtering. Consider all of the worst-case signals during the system design – internal to the board, and incoming from off the system. Part of the system DFMEA review should ask the design team – “What outside electrical interference could cause this system to fail”?
Identify Initial Conditions
The initial start-up condition for a system can often be neglected. The steady-state operation is the most valuable and the mode that is given the most attention. However, this initial operation time may be the most severe, electrically, to the design. A proper review should model all the transients and inrush current at turn-on. It is during this stage that capacitors first charge and transient spikes could be observed at the internal component pins. Microcontrollers enter a boot sequence where memory is read and initial activity takes place. The current consumption during this phase is higher and must be modeled during the design phase of the project. This unusual, but predictable, power activity could create scenarios where component maximum tolerances are exceeded.
Inspect the Corners
While nominal system conditions are pleasing for performance reasons, the minimum and maximum scenarios cannot be ignored since they will be a required use case. The complex system design must consider all of the corner cases of elevated supply, extreme temperatures, and environmental conditions such as humidity and EMC, maximum loading and computation. In fact, if the corner operation cases perform well, it may preclude the need to test the system at a nominal condition.
Keep the Smoke Inside
The first verification step for a new system is to turn it on and check for unwanted smoke. Inadvertent errors can cause issues at this first step. Properly review the system requirements, layout, BOM and corner cases to mitigate these issues. Work with your CM to understand minimum pitch and assembly challenges in advance of fabrication. On your next project, make sure to keep the smoke inside the components and don’t let it out in the open.
Inspect the Corners
By carefully reading the manufacturer's guidelines, users can avoid exceeding the recommended operating conditions. Additionally, maintaining proper power management, using correct wiring techniques, and ensuring proper grounding can help prevent the release of magic smoke. Regular maintenance and inspection of electronic devices are also essential to identify any potential issues early on and address them before they cause significant damage. In conclusion, while the concept of magic smoke electronics is a humorous way of referring to the failure or malfunction of electronic devices, it serves as a reminder of the importance of proper handling, maintenance, and understanding of electronic components. By following guidelines and being cautious, users can minimize the risk of releasing the magic smoke and prolong the lifespan of their electronic devices..
Reviews for "The Smoke is Rising: Exploring the Future of Electronic Component Protection"
- Sarah - 1/5 stars - I had such high hopes for Magic Smokr Electronics, but I was thoroughly disappointed with my experience. The customer service was terrible, with long wait times and unhelpful representatives. Additionally, the quality of their products was subpar. The device I purchased stopped working after just a few uses, and when I contacted their support team, they were unresponsive and unapologetic. I would not recommend this company to anyone.
- John - 2/5 stars - I was excited to try out Magic Smokr Electronics, but unfortunately, I was let down by their products. The vape pen I purchased had a faulty battery and would randomly turn off while I was using it. I tried reaching out to their customer service multiple times, but I never received a response. It was frustrating not being able to use the product properly and not having any assistance from the company. I would caution others to think twice before purchasing from Magic Smokr Electronics.
- Emily - 2/5 stars - My experience with Magic Smokr Electronics was less than satisfactory. The e-cigarette I bought from them was not only expensive but also did not provide the experience I was expecting. The flavors were weak and not as advertised. Additionally, the battery life was significantly shorter than promised. I reached out to their customer service to express my disappointment, but they were unhelpful and dismissive. Overall, I regret my purchase and would not recommend this brand to others.